The Oracle Interface Configuration Tool (OIFCFG) command-line interface helps you to define and administer network interfaces. You can use OIFCFG commands Oracle Clusterware environments to:
Allocate and deallocate network interfaces to components
Direct components to use specific network interfaces
Retrieve component configuration information
This appendix includes the following topics:
Before you invoke OIFCFG, ensure that you have started Oracle Clusterware on at least the local node and preferably on all nodes if you intend to include the -global option in the command syntax.
Note:
To change the global network interface, Oracle Clusterware must be running on all cluster nodes.Run OIFCFG from the Grid_home/bin/ directory as the user who installed the Oracle Clusterware software. For example:
$ ./oifcfg
Run the oifcfg -help command to display online help for OIFCFG.
$ ./oifcfg -help
This section contains the following topics:
oifcfg iflist [-p] [-n]
oifcfg setif {-node nodename | -global} {if_name/subnet:if_type[,if_type]}[,...]
oifcfg getif [-node nodename | -global] [ -if if_name[/subnet] [-type if_type]]
oifcfg delif {{-node nodename | -global} [if_name[/subnet]] [-force] | -force}
oifcfg [-help]
You can enter any of the OIFCFG commands listed in Table D-1.
| Command | Description |
|---|---|
|
|
Shows the available interfaces that you can configure with
If the interface has an IPv6 network, then OIFCFG prints the IPv6 subnet on a separate line, similar to the following: eth1 fec0::80 PUBLIC 64 eth1 10.229.184.0 PUBLIC 255.255.248.0 |
|
|
Sets an interface type (public, cluster interconnect, or Oracle ASM) for an interface. |
|
|
Displays the interfaces for which an interface type has been defined with the |
|
|
Deletes the stored network configuration for global or node-specific interfaces. You can use the |
This section lists the parameters for the OIFCFG commands. Note that some parameters are optional, depending on which command you run.
The name of the Oracle Clusterware node as listed in the output from the olsnodes command. Appendix C, "OLSNODES Command Reference" describes the olsnodes command.
A network interface can be stored as a global interface (as reported by the iflist command) or as a node-specific interface:
An interface is stored as a global interface when all of the nodes of an Oracle Real Application Clusters (Oracle RAC) cluster have the same interface connected to the same subnet. The global interface (and configuring all nodes with the same network interface for each public subnet and the same network interface for each private subnet) is not only the recommended configuration, but it is also the default installation configuration.
An interface can be stored as a node-specific (local) interface.
Note:
Oracle supports interface name wildcards for different interface names across nodes. Oracle does not support using-node to configure different specific interface names on different nodes.The name by which the interface is configured in the system.
The subnet address of the interface.
One or more comma-delimited interface types: public, cluster_interconnect, or asm.
Display online help for OIFCFG commands.
A network interface specification takes the following form:
if_name/subnet:if_type
The specification uniquely identifies the network interface using the:
Interface name
When using the oifcfg setif command, you can specify interface names that contain wildcard characters, such as an asterisk (*), which matches any string. However, you must surround interface names that contain wildcards with double quotation marks ("").
Note:
Oracle recommends that you do not use wildcards in a cluster with pre-Oracle Database 11g release 2 (11.2.0.2) databases because Oracle resolves the interface name by expanding the wildcard on the local node and also issues a PRIF-0029 warning every time you run theoifcfg getif command.
If you use wildcards with Oracle Databases that are pre-11g release 2 (11.2.0.2), then those databases must use the CLUSTER_INTERCONNECTS parameter, instead.
Associated subnet
Interface type
The interface type indicates the purpose for which the network is configured. The supported interface types are:
public: An interface that can be used for communication with components external to Oracle RAC instances, such as Oracle Net and Virtual Internet Protocol (VIP) addresses.
cluster_interconnect: A private interface used for the cluster interconnect to provide interinstance or Cache FusionFoot 1 communication.
If you set the interface type to cluster_interconnect, then it affects instances as they start and changes do not take effect until you restart the instances.
For example, the following specification identifies qfe0 as a cluster interconnect located at the address 204.152.65.0:
qfe0/204.152.65.0:cluster_interconnect
The Oracle Universal Installer uses OIFCFG to identify and display available interfaces.
The effect of changing the interface names depends on which name you are changing, and whether you are also changing the IP address. In cases where you change only the interface names, the ramifications are minor. If you change the name for the public interface that is stored in the Oracle Cluster Registry (OCR), you must modify the nodeapps for each node. Therefore, you must stop the nodeapps for this change to take effect.
You must restart Oracle Clusterware on all members of the cluster when you make global changes. For local changes, you need only to perform a node restart. Interconnect changes for the database occur at instance startup. However, the interconnect for Oracle Clusterware might be different.
Because interconnects are chosen when instances start, just issuing OIFCFG commands does not have an immediate effect on the running system. Instead, changes take effect after restarting the component that might be affected by the command.
Changes you make to cluster-wide network classifications with OIFCFG require all known cluster nodes to be up so that their Grid Plug and Play profiles can be updated.
The following examples show some common uses for the OIFCFG commands.
You can use OIFCFG to list the interface names and the subnets of all of the interfaces available on the local node by executing the iflist keyword, as shown in this example:
oifcfg iflist eth0 172.19.141.0 eth1 172.21.65.0
You can also retrieve specific OIFCFG information with a getif command.
For example, after you install Oracle Clusterware, you can verify that the public and cluster interconnect have been set to the desired values by entering the following command:
$ oifcfg getif
This command returns values for global public and global cluster_interconnect, similar to the following:
eth0 172.19.141.0 global public eth1 172.21.65.0 global cluster_interconnect
To store an interface, use the setif keyword. For example, to store the interface eth0, with the subnet 172.19.141.0, as a global interface (to be used as an interconnect for all of the Oracle RAC instances in your cluster and Oracle Clusterware), use the command:
oifcfg setif -global eth0/172.19.141.0:cluster_interconnect
Note:
Ensure that all nodes are running when you run thesetif command because Oracle cannot update Grid Plug and Play profiles on nodes that are not running.Use the oifcfg delif command to delete the stored configuration for global or node-specific interfaces. A specific node-specific or global interface can be deleted by supplying the interface name, with an optional subnet, on the command line.
Note:
If you only enteroifcfg delif, with no other arguments given on the command line, then OIFCFG deletes all interfaces on all nodes in the cluster.For example, the following command deletes the global interface named eth1 for the subnet 172.21.65.0:
oifcfg delif -global eth1/172.21.65.0
The following command deletes all of the global interfaces assigned with OIFCFG:
oifcfg delif -global
Footnote Legend
Footnote 1: Cache Fusion is a diskless cache coherency mechanism that provides copies of blocks directly from a holding instance's memory cache to a requesting instance's memory cache.